Fish-Hawk.Net

Hi guys,

I picked up a Helix 7 at the boat show this spring(winter actually) and will be mounting here in the next couple weeks hopefully. Curious what your thoughts or recommendations would be. This will be a cockpit mount as well. I have FishHawk 1650 SC. The boat is still all wrapped up so i haven't been able to test fit it yet, but I'm thinking it might be a bit a tight. I'm thinking of using the RAM mount with the shorter arm. https://www.rammount.com/part/RAM-202-24-B-202U I just don't know if the normal arm will be too big for the dash and the windshield.

Thanks!

I would say it depends on where you plan on mounting the ram. I'm sure there is a location that the regular length arm will work but the shorter arm will do just as good.

I had something similar to what you have linked on my previous boat and they do work. I did find however, that they did loosen over time and one good wave would move the fishfinder around pretty good. If I had to replace it, I would have looked at something a little different and even though of going with this one instead (A little more expensive) https://www.rammount.com/part/RAM-109HU as it would have alleviated any of the minor issues I had with the mount I went with.

I also have a Ram mount on a Lund Rebel 1625, I got one with the longer arm so it can swivel and be used when fishing from the bow.
It does not look like they make that model anymore, (2008) but the new one looks OK.

I'd roll with the shorter arm if possible. Lock er down and she shouldn't ever move. If you get the longer one it may have room to fall...

RJ

RJ wrote:I'd roll with the shorter arm if possible. Lock er down and she shouldn't ever move. If you get the longer one it may have room to fall...

RJ

5oclocksomewhere wrote:I also have a Ram mount on a Lund Rebel 1625, I got one with the longer arm so it can swivel and be used when fishing from the bow.
It does not look like they make that model anymore, (2008) but the new one looks OK.

Now you both have me thinking.. I didn't consider this one. It does sit a little taller, i'm not sure if the windshield will be in the way or not.. I can always rotate it a little forward if need be.

RJ wrote:I'd roll with the shorter arm if possible. Lock er down and she shouldn't ever move. If you get the longer one it may have room to fall...

RJ

Looks like the wrapping might be coming off a little sooner than expected. take some measurements and snap a couple pictures.

I think you're on the right track.

No sense rushing into this and doing something you'll regret. Take some good measurements and go from there.

I have 52 days until opener. I have a little time. but I'm sure before i know it. it'll be here.. I can't wait!

I can imagine what you are feeling. I bought a new boat in December and am Having Helix 10's put on it. This will be a completely different experience from boat, motor, speed as well as fishfinders.

I had smaller, less capable units on my old boat and I can't wait to check out the new features just like you!

I'm sure you can't wait either. What did you upgrade to?

coming out of a Bass Tracker PT190TX and jumping into a Ranger Z119c. Should be a blast.

I've used the RAM swing arm that is in the pictures. Really like it. I just loosen the friction knob and can swing the mount so I can see it from anywhere in the boat.

Your options might be limited with a windshield.

I bought mine from GPS City. Good selection, prices and service. Some mounts might be backordered, so I wouldn't leave your choice until the last minute.

Good luck.

Sorry for the long delay in getting back. Life happens. I finally on the Helix 7 mounted the day before opener. I'll get a couple pics soon. But i ended up using a RAM.
https://www.rammount.com/part/RAM-202-24-202U

Works perfectly. I think i'm also going to pick up another ball, "Y" splitter and run an additional set of cables to he bow where the trolling motor is. It'll be easy to connect and disconnect.

sholtz wrote:Sorry for the long delay in getting back. Life happens. I finally on the Helix 7 mounted the day before opener. I'll get a couple pics soon. But i ended up using a RAM.
https://www.rammount.com/part/RAM-202-24-202U

Works perfectly. I think i'm also going to pick up another ball, "Y" splitter and run an additional set of cables to he bow where the trolling motor is. It'll be easy to connect and disconnect.

Pics as promised.